The Slotted/Pozidriv is slightly different from the Slotted/Phillips (PH/S), and good use requires special screwdrivers. [ citation needed] ACR Phillips II Plus [ edit ] Chilton, G. (2001). Homebasics: the complete guide to running today's home. Barnes & Noble Books. p. 18. ISBN 978-0-7607-2719-5 . Retrieved 27 September 2018. A screwdriver is classified by its tip, which is shaped to fit the driving surfaces (slots, grooves, recesses, etc.) on the corresponding screw head. Proper use requires that the screwdriver's tip engage the head of a screw of the same size and type designation as the screwdriver tip. Screwdriver tips are available in a wide variety of types and sizes ( List of screw drives). The two most common are the simple 'blade'-type for slotted screws, and Phillips, generically called "cross-recess", "cross-head", or "cross-point". The Phillips Screw Company". phillips-screw.com. Archived from the original on 2021-10-08 . Retrieved 2021-10-07.

Avsafe". www.losspreventionfasteners.com. Archived from the original on 2017-03-01 . Retrieved 2017-02-28. There are multiple sizes of Phillips head screwdrivers, with tip measurements sometimes varying by just half a millimeter. With such a small size difference, can’t you get away with using the wrong driver on the wrong screw?Chart of Torx fasteners and tools". Wiha Tools USA. Archived from the original on 2015-12-26 . Retrieved 2012-01-14. Torx Paralobe is a further improvement over Torx Plus, [48] claiming 50% increased drive system torque over Torx and 20% over Torx Plus. Though most casual DIYers will not need it in their toolkit, Phillips makes a very small #000 screw and matching 000 Phillips head screwdriver. This very small screwdriver is used in precision work involving compact electronics. How are screwdriver sizes measured? Adler, Alexander (1998-05-18). Testing and Understanding Screwdriver Bit Wear (Master's thesis). Virginia Tech. hdl: 10919/36701. Also known as an ECX or Combination Tip drive. A combined slotted and Robertson drive screw found in electrical power equipment and distribution equipment. The design allows for higher torque application with reduced camming, slipping out and damaging the fastener. [63] The ECX drive is not compatible with older combination Phillips and slotted head screws. [64] Although Milwaukee Electric Tool holds the trade name ECX, their marketing materials do not tell what type of screw head ECX is designed to fit. [50] Clutch [ edit ]

Different shaft lengths and handle sizes can make it easier to work on whatever you're working on. A longer shaft can allow you to access hard-to-reach areas where your hand won't fit.

You can only compare up to four products at a time.

The earliest documented screwdrivers were used in the late Middle Ages. They were probably invented in the late 15th century, either in Germany or France. The tool's original names in German and French were Schraubenzieher [2] [3] [4] [ circular reference] (screw-tightener) and tournevis (turnscrew), respectively. The first documentation of the tool is in the medieval Housebook of Wolfegg Castle, a manuscript written sometime between 1475 and 1490. [5] These earliest screwdrivers had pear-shaped handles and were made for slotted screws (diversification of the many types of screwdrivers did not emerge until the Gilded Age). The screwdriver remained inconspicuous, however, as evidence of its existence throughout the next 300 years is based primarily on the presence of screws. The 12-pointed internal star shape superficially resembles the "double hex" fastener head, but differs subtly in that the points are shaped to an internal angle of 90° (derived from a square), rather than the 120° internal angle of a hexagon. In practice, drivers for the fasteners may be interchangeable, but should be examined carefully for proper fit before application of force. A hex key should not be used where a key of square cross-section is the correct fit. Apple uses Y-type screws to secure the battery on the 2010 and 2011 MacBook Pro, as well as an extremely small type in the Apple Watch, iPhone 7 and iPhone X. [87] [88] This style of screw is often called a "tri-wing", although that name more properly belongs to a different design (see below). Any complete screwdriver set will feature both flat head and Phillips’s head screwdrivers, with the size of the drivers ranging from 0 to 4 while the handle and shaft will length vary. In a set, you might find a special stubby Phillips-head driver with a 1½-inch shaft, and several drivers with four-inch shafts as well. Recessed head fastener and driver combination". Google Patents. 2015-12-11. Archived from the original on 2020-01-26 . Retrieved 2017-10-13.