Before reconnecting the white Lego pieces which make up the front bonnet, ensure that the cables from the LEDs are laid in between the studs of the Lego plates underneath as per below example images. Our light kits come with detailed, step-by-step installation guides to help you add lights to your favourite models. No electronics experience required! Connect multiple kits To find a lighting kit for your LEGO® set, simply scroll and browse below to find the appropriate light up kit. You can also use the search function above and type in the model name or number to find your set. Reconnect the transparent blue triangular plates we removed earlier on top of the additional plates we just installed. KIT itself : really nice KIT. You just simply can not compare to "without light" KIT. That is an another level.

Take the white 4×4 plate with pieces attached and disassemble the pieces as we will be replacing the 2 grey pieces. This kit has not one, but two sound modules, and together these modules can play four sounds at the same time. This provides the most realistic sound possible, including: Connect the cables from the tail lights into one of the 12-port expansion boards ( expansion board#1) by first winding them around the board before connecting them into the first 2 available ports. We are winding them around the board so that we don’t have too much excess cabling to have to hide later on. Before dive into the KIT itself I have to remark, that the customer service was just fantastic before buying the KIT. I had some doubts and questions but they were just provided one of the best support online. One 3-Voice Polyphonic Sound Chip with Ecto-1 Siren, Engine, Door, and Alarm Sound EffectsPre-LoadedTake the 5cm connecting cable from the kit and connect it to the last available port on expansion board#2. Take another flashing Bit light and install it to this section ensuring that the LED is laid over the white stud and secured down by reconnecting the red piece over the top.

Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it. PLEASE NOTE: THIS IS ONLY LeLightGo LEGO LIGHTS. LEGO® SET IS NOT INCLUDED. ABOUT WARRANTY & SERVICE Genuine LEGO® Parts for the Movie-Accurate Replacement Roof Strobe, Motor, and to Hold Adapters and Controllers in PlaceTake the 2 provided Lego 1×6 white pieces and connect them underneath the roof securing the front and middle roof sections together. One of LEGO®'s most popular product lines can now be brought to life with our custom LED lighting system. Browse our catalogue of Star Wars designed light kits, which include Ultimate Collector Series (UCS) sets and LED lightsabers for minifigures! LEGO® Modular Building Series When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between. The LEGO Ghostbusters Ecto 1 (21108) is a faithful recreation of the iconic vehicle from the hit 80s movie franchise, Ghostbusters! Remove the following pieces from the 2×6 plate and then connect one of the provided grey 1×2 Lego plates on each side as per below.

We will be installing lights to the headlights first. To do this, remove the following pieces from the front of the car. To ensure a trouble-free installation of your light kit, please read and follow each step carefully. We will now install flasing LEDs to the blue spot lights at the front. Remove the grey plates with clips from the pole and then disconnect the round blue pieces from them. Take the 2 groups of cables from the roof lights and loop them around so that we do not have too much excess cabling. Use some tape to tape the cables together to prevent them from unwinding.Remove the front section with the grill and number plate attached, followed by the 2 Lego 2×4 plates with light pieces attached. CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light. Connecting cable connectors to Expansion Boards Authentic Cadillac ambulance engine sound that loops until you stop it. Includes unique start and stop sounds, and even a great"engine stall" sound that will be triggered 40% of the time when you start the engine. Follow LeLightGo step-by-step instruction to light up your Ghostbusters ECTO-1, something amazing will happen at night. All our kits are plug and play - no electronics knowledge needed! Repeat this step for the cables from the tail lights, twisting/winding them around each other. We should now have 2 groups of cables.

Take the front grey pole with attached lights and disassemble all the pieces as we will be replacing the grey pieces with new pieces (with different clips). Take 1 standard Bit Light (non flashing) and place it on top of the stud of the grey round plate ensuring the LED component part is facing the correct way up. Secure the LED in place by connecting the transparent Lego plate over the top. Turn the roof on its side to allow you to then group all the cables from the front roof LEDs. Twist/wind them around each other, same way we did for the rest of the light cables. Take the cable from the LED we just installed and the 2 cables from the front right lights and hide them in between studs up the right side of the car by reconnecting the grey triangular plates over the top of them.It’s time to neaten up all the cabling from the LEDs we have installed so far. Take the 5 cables from the front lights and twist/wind them around each other starting from the base working your way up. They should all come together neatly. Take the front section of the roof and remove the white roof plate from underneath, then remove the transparent blue triangular pieces, followed by the grey pole with attached light pieces.